Guides

Star Trac error codes: the 10 we see most, and what to do

Most Star Trac commercial treadmills show a short message when they detect a fault, such as "Elevation Stall" or "Check Speed System," and smaller models like the 4-TR show a numbered MCU error. These are the 10 messages our technicians see most often in gyms, apartment communities and hotels, what each one means in plain words, and the one safe thing your staff can check first.

● Factory-trained technicians● All major brands serviced
● Fully insured● Upfront pricing, always

Request service

One short form. We reply the same business day, Monday through Friday.

"*" indicates required fields

This field is for validation purposes and should be left unchanged.
Name*

Before you do anything

  1. Write the message or code down exactly as it shows on the screen.
  2. Turn the machine off, wait one minute, and turn it back on. Do this once.
  3. If the message comes back, take the machine out of use and put up an Out of Order sign. Free printable Out of Order sign
  4. Call ServiceRX at 888-383-6371. We repair Star Trac equipment in North Carolina and South Carolina.

What does Check Motor System mean on a Star Trac treadmill?

Think of it like the check engine light in a car. The drive system found a problem, such as the motor pulling too much current, but the message does not say which part. A technician reads the stored fault record to find the cause. Common causes are a dirty or worn belt and deck, a power problem, or the motor control board. Stop using the treadmill and call for service.

What does Check Speed System mean on a Star Trac treadmill?

Also a check engine light, this time for the system that measures belt speed. It usually points to the speed sensor, its wiring, or the motor control board. Restart once. If it comes back, call for service.

What does Speed Change mean on a Star Trac treadmill?

The belt sped up or slowed down faster than the treadmill allows. A worn belt and deck, a loose speed sensor, or a drive problem can cause it. Restart once. If it comes back, call for service.

What does Elevation Stall mean on a Star Trac treadmill?

The treadmill told the incline to move and saw no movement. Check that nothing under or behind the machine is blocking the incline, then restart once. If it comes back, call for service. Elevation systems that are not cleaned and lubricated on schedule are a common cause.

What does Elevation Range mean on a Star Trac treadmill?

The incline went higher or lower than the limits set for that treadmill. The incline sensor or its calibration is usually the cause. Restart once. If it comes back, call for service.

What does Elevation Lost mean on a Star Trac treadmill?

The treadmill lost the signal from the sensor that tells it the incline position. It is usually the sensor or its cable. Restart once. If it comes back, call for service.

What does Key Down mean on a Star Trac treadmill?

The treadmill thinks a button is being held down. It can be any keypad, including the speed and incline keys on the handlebar. Make sure nothing is resting on the console or handlebar and that no key is stuck, then restart once. If it comes back, a keypad needs service.

What does No Rail Stop mean on a Star Trac treadmill?

The treadmill cannot detect its stop switch, usually the red stop button or safety clip on the handrail. Make sure the stop switch is set in its run position and the safety clip is attached, then restart once. If it comes back, the switch or its wiring needs service.

What does MCU Error 1 mean on a Star Trac treadmill?

On models that show numbered MCU errors, such as the 4-TR, error 1 means the treadmill is not reading belt speed. The speed sensor is loose, unplugged or failing. Restart once. If it comes back, call for service.

What does MCU Error 5 mean on a Star Trac treadmill?

The console and the motor control board stopped talking to each other. It is most often the cable between them, sometimes one of the boards. Restart once. If it comes back, call for service.

Free printable

Fitness Equipment Maintenance Log

A 5-page log for your facility: a preventive maintenance checklist, an equipment list, a page per machine, and a staff problem report. Print it and keep it in a binder.

Download the maintenance log (PDF)

Message keeps coming back?

Take the machine out of use, put up the Out of Order sign, and call ServiceRX at 888-383-6371. Factory-trained technicians, North Carolina and South Carolina.

Request service
or call 888-383-6371
Call nowRequest service